Hello ISDN Users.

I am hit by some frustrations because my Server has only two PCI-X slots
and my Eicon Diva 4BRI-8M, which should work fine with Asterisk, is only
PCI 2.0 standard and does not fit into the PCI-X slot.

Currently I use two AVM Fritz! cards, but while my Xeon 604 2000MHz had
a load-average of less then 0.5 it is now increasing to more then 4, if
I have 20 VoIP and two ISDN calls.

So, the cheap AVM cards have to replaced.

Since I do not have currenly the money to buy a Eicon Diva Server 3.0
quad-port, can you recommend me inexpensive Dual- or Quad-Port cards
which I could get used on eBay?

Note: I have to connect my Alice Box (ADSL2+) and two Vodafone
EasyBox 803A (using the Huawei K3765-HV USB-Stick) to it.

Thanks, Greetings and nice Day/Evening
Michelle Konzack

I am looking for a GSM Gateway or GSM PCI Card with minimum of 6 Sim Cards
slots.

Which one do you recommend and easier to setup?

As long it work on UK mobile network and make 6 calls simultaneously.

Thanks

I am looking for a GSM Gateway or GSM PCI Card with minimum of 6 Sim Cards
slots.

Which one do you recommend and easier to setup?

As long it work on UK mobile network and make 6 calls simultaneously.

Thanks

On Mon, 2012-05-07 at 10:26 -0500, Russ Meyerriecks wrote:
> There were a few compatability issues with the tdm400′s pci interface chip
> and certain motherboards

Interesting idea, but it’s been running in this same server with the
same motherboard for at least two years now, and this problem started
only last week.

At this point, I am sure enough that the card has failed that I have
ordered a new base card. If I’m wrong, I will only be out return postage
and 10% restock fee.

Dear;

We are using ISDN PRI, and the telephony card is Digium card supported 2 ports of E1s, and in the system.conf, I selected the zone to be uk loadzone = uk (loadzone = uk and defaultzone=uk). Actually the Asterisk in Jordan and connected to Jordan Telecom provider.

This is the output of some commands that help to give the specification of the hardware:

[root@CC dahdi]# dahdi_hardware
pci:0000:05:08.0 wct4xxp+ d161:1220 Wildcard TE220 (5th Gen)

[root@CC dahdi]# dahdi_scan
[1]
active=yes
alarms=OK
description=T2XXP (PCI) Card 0 Span 1
name=TE2/0/1
manufacturer=Digium
devicetype=Wildcard TE220 (5th Gen) (VPMOCT064)
location=Board ID Switch 0
basechan=1
totchans=31
irq=34
type=digital-E1
syncsrc=1
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=AMI,HDB3
framing_opts=CCS,CRC4
coding=HDB3
framing=CCS/CRC4
[2]
active=yes
alarms=UNCONFIGURED
description=T2XXP (PCI) Card 0 Span 2
name=TE2/0/2
manufacturer=Digium
devicetype=Wildcard TE220 (5th Gen) (VPMOCT064)
location=Board ID Switch 0
basechan=32
totchans=31
irq=34
type=digital-E1
syncsrc=1
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=AMI,HDB3
framing_opts=CCS,CRC4
coding=
framing=CAS

Regards
Bilal