Cisco Spa Phones And Sal

Home » Asterisk Users » Cisco Spa Phones And Sal
Asterisk Users 2 Comments

Hi
   I have been trying for several days get 3 Cisco spa508g phones
(firmware 7.5.5) to work with asterisk 11.6 cert1 and sla. I can get the phones to all ring when an incoming call arrives, and I see the slatrunk working. However the blf function does not work. If one extension picks up the call the others do not show the trunk in use. 
And as you might expect the hold and outbound dialing does not work. I
do not think the problem is with the sla config on asterisk, but rather the setup in the phone. Does anyone have an example config for the spa phones.

Thanks

Kelly

————————-
Email sent using Atmail – Email, Groupware and Calendaring done right.

2 thoughts on - Cisco Spa Phones And Sal

  • T25lIHF1aWNraWUgdGhhdCB1c3VhbGx5IGdldHMgbWU6DQoNCk9uIHRoZSDigJxBdHRlbmRhbnQg Q29uc29sZeKAnSB0YWIsIHRoZXJlIGlzIGEg4oCcU2VydmVyIFR5cGXigJ0gc2V0dGluZyBpbiB0
    aGUgR2VuZXJhbCBzZWN0aW9uIHRoYXQgZGVmYXVsdHMgdG8gQnJvYWRjb20uICBUaGlzIG5lZWRz IHRvIGJlIGNoYW5nZWQgdG8gQXN0ZXJpc2sgZm9yIEFOWSBCTEYgb24gdGhlIHBob25lIHRvIHdv cmsgKHJlZ2FyZGxlc3Mgb2Ygd2hldGhlciBvciBub3QgeW914oCZcmUgZG9pbmcgQkxGIG9uIHRo ZSBwaG9uZSBpdHNlbGYgb3IgdmlhIGFuIGF0dGVuZGFudCBjb25zb2xlKS4gIFRoaXMgdGFiIGlz IG9ubHkgYWNjZXNzaWJsZSB3aXRoaW4gdGhlIC9hZG1pbi9hZHZhbmNlZCB3ZWIgaW50ZXJmYWNl LCBvciB5b3UgY2FuIHVzZSB0aGUgPFNlcnZlcl9UeXBlPiBjb25maWd1cmF0aW9uIG9wdGlvbiB3
    aXRoaW4gdGhlIHBzZXVkby1YTUwgY29uZmlnIGZpbGVzLCBpZiB5b3XigJlyZSBkb2luZyBhdXRv IHByb3Zpc2lvbmluZy4NCg0KTm9haCBFbmdlbGJlcnRoDQpNZXRhTElOSyBUZWNobm9sb2dpZXMN
    Cg0KRnJvbTogYXN0ZXJpc2stdXNlcnMtYm91bmNlc0BsaXN0cy5kaWdpdW0uY29tIFttYWlsdG86
    YXN0ZXJpc2stdXNlcnMtYm91bmNlc0BsaXN0cy5kaWdpdW0uY29tXSBPbiBCZWhhbGYgT2Yga2Vs bHlAbmN3Y29tLmNvbQ0KU2VudDogU3VuZGF5LCBNYXJjaCAwMiwgMjAxNCAxMjowNCBQTQ0KVG86
    IGFzdGVyaXNrLXVzZXJzQGxpc3RzLmRpZ2l1bS5jb20NClN1YmplY3Q6IFthc3Rlcmlzay11c2Vy c10gY2lzY28gc3BhIHBob25lcyBhbmQgc2FsDQoNCkhpDQogICBJIGhhdmUgYmVlbiB0cnlpbmcg Zm9yIHNldmVyYWwgZGF5cyBnZXQgMyBDaXNjbyBzcGE1MDhnIHBob25lcyAoZmlybXdhcmUgNy41
    LjUpIHRvIHdvcmsgd2l0aCBhc3RlcmlzayAxMS42IGNlcnQxIGFuZCBzbGEuIEkgY2FuIGdldCB0
    aGUgcGhvbmVzIHRvIGFsbCByaW5nIHdoZW4gYW4gaW5jb21pbmcgY2FsbCBhcnJpdmVzLCBhbmQg SSBzZWUgdGhlIHNsYXRydW5rIHdvcmtpbmcuIEhvd2V2ZXIgdGhlIGJsZiBmdW5jdGlvbiBkb2Vz IG5vdCB3b3JrLiBJZiBvbmUgZXh0ZW5zaW9uIHBpY2tzIHVwIHRoZSBjYWxsIHRoZSBvdGhlcnMg ZG8gbm90IHNob3cgdGhlIHRydW5rIGluIHVzZS4gIEFuZCBhcyB5b3UgbWlnaHQgZXhwZWN0IHRo ZSBob2xkIGFuZCBvdXRib3VuZCBkaWFsaW5nIGRvZXMgbm90IHdvcmsuIEkgZG8gbm90IHRoaW5r IHRoZSBwcm9ibGVtIGlzIHdpdGggdGhlIHNsYSBjb25maWcgb24gYXN0ZXJpc2ssIGJ1dCByYXRo ZXIgdGhlIHNldHVwIGluIHRoZSBwaG9uZS4gRG9lcyBhbnlvbmUgaGF2ZSBhbiBleGFtcGxlIGNv bmZpZyBmb3IgdGhlIHNwYSBwaG9uZXMuDQoNClRoYW5rcw0KDQpLZWxseQ0KX19fX19fX19fX19f X19fX19fX19fX19fX19fX19fX18NCkVtYWlsIHNlbnQgdXNpbmcgQXRtYWlsIC0gRW1haWwsIEdy b3Vwd2FyZSBhbmQgQ2FsZW5kYXJpbmcgZG9uZSByaWdodC4NCg=

  • Thanks for the reply

     I did have it set to asterisk but the Attendant Console Call Pickup Code:was set to *8 (asterisk default)  For some reason *8 would give a forbidden message on the screen of the phone. So I changed it to #8
    and changed the features.conf file to reflect that. It works now except that the phone does not ring. The blf lights flash on the phones and when you answer one of them the line shows in use on all phones. Park the call on one phone and you can pick it up on any other phone just by hitting the line button. If you pick up the line it dials asterisk and gives you a dial tone on the sla trunk.

    My biggest problem now is that the phones don’t ring. Below are my configs. I would greatly appreciate any input.

    sla.conf

    [general]
    attemptcallerid=yes

    [line1]
    type=trunk device=DAHDI/1-1
    autocontext=line1
    hold=open

    [line2]
    type=trunk device=DAHDI/1-2
    autocontext=line2

    [station](!)
    type=station autocontext=sla_stations ringtimeout=30
    ringdelay=1
    trunk=line1

    [8*5001](station)
    device=SIP/5001

    [8*5002](station)
    device=SIP/5002

    dialplan show lists

    [ Context ‘line1’ created by ‘SLA’ ]
      ‘s’ =>            1. SLATrunk(line1)                           
    [SLA]

    [ Context ‘line2’ created by ‘SLA’ ]
      ‘s’ =>            1. SLATrunk(line2)                           
    [SLA]

    [ Context ‘sla_stations’ created by ‘SLA’ ]
      ‘8*5001’ =>       1. SLAStation(8*5001)                        
    [SLA]
      ‘8*5001_line1’ => hint:
    SLA:8*5001_line1                        [SLA]
                        1. SLAStation(8*5001_line1)                   [SLA]
      ‘8*5002’ =>       1. SLAStation(8*5002)                        
    [SLA]
      ‘8*5002_line1’ => hint:
    SLA:8*5002_line1                        [SLA]
                        1. SLAStation(8*5002_line1)                   [SLA]

    on phone 1

    ext 1 enabled yes username 100
    password  password

    ext 2 enabled no

    phone tab

    line key 1
    extension 1
    share call appearance private short name 100

    line key 2
    extension disabled share call appearance private short name line 1
    extended function fnc=blf+cp+sd;sub=8*5001_line1@$PROXY;ext=8*5001_line1@$PROXY

    on phone 2

    ext 1 enabled yes username 101
    password  password

    ext 2 enabled no

    phone tab

    line key 1
    extension 1
    share call appearance private short name 101

    line key 2
    extension disabled share call appearance private short name line 1
    extended function fnc=blf+cp+sd;sub=8*5002_line1@$PROXY;ext=8*5002_line1@$PROXY

    Kelly

    —– Original Message —–
    From: “Asterisk Users Mailing List – Non-Commercial Discussion”
    To:”Asterisk Users Mailing List – Non-Commercial Discussion”
    Cc:
    Sent:Sun, 2 Mar 2014 23:33:03 +0000
    Subject:Re: [asterisk-users] cisco spa phones and sal

    One quickie that usually gets me:

     

    On the “Attendant Console” tab, there is a “Server Type”
    setting in the General section that defaults to Broadcom.  This needs to be changed to Asterisk for ANY BLF on the phone to work (regardless of whether or not you’re doing BLF on the phone itself or via an attendant console).  This tab is only accessible within the
    /admin/advanced web interface, or you can use the configuration option within the pseudo-XML config files, if you’re doing auto provisioning.

     

    Noah Engelberth

    MetaLINK Technologies

     

    FROM: asterisk-users-bounces@lists.digium.com
    [mailto:asterisk-users-bounces@lists.digium.com] ON BEHALF OF
    kelly@ncwcom.com SENT: Sunday, March 02, 2014 12:04 PM
    TO: asterisk-users@lists.digium.com SUBJECT: [asterisk-users] cisco spa phones and sal

     

    Hi
       I have been trying for several days get 3 Cisco spa508g phones
    (firmware 7.5.5) to work with asterisk 11.6 cert1 and sla. I can get the phones to all ring when an incoming call arrives, and I see the slatrunk working. However the blf function does not work. If one extension picks up the call the others do not show the trunk in use. 
    And as you might expect the hold and outbound dialing does not work. I
    do not think the problem is with the sla config on asterisk, but rather the setup in the phone. Does anyone have an example config for the spa phones.

    Thanks

    Kelly

    Email sent using Atmail – Email, Groupware and Calendaring done rig1

    ————————-
    Email sent using Atmail – Email, Groupware and Calendaring done right.