TE410P hardware problems

Home » Asterisk Users » TE410P hardware problems
Asterisk Users 2 Comments

TE410P card down.

I have three (3) TE410P in one machine running asterisk with SS7.

My problems started last week when one of my cards started switching to E1
every time after reboot. I set the following in dahdi.conf and that solve
the problem.

/etc/modprobe.d/
options wct4xxp t1e1override=0x00

Now all 4 ports on that card is down with Red Alarm. I tried rebooting the
machine and restarting dahdi with no luck. The other two cards are working
fine. I put a loop plug the ports and same problem.

dahdi_scan
[9]
active=yes
alarms=RED/LFA/LMFA
description=T4XXP (PCI) Card 2 Span 1
name=TE4/2/1
manufacturer=Digium
devicetype=Wildcard TE410P (4th Gen) (VPMOCT128)
location=PCI Bus 10 Slot 04
basechan=193
totchans=24
irq=50
type=digital-T1
syncsrc=0
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=B8ZS,AMI
framing_opts=ESF,D4
coding=B8ZS
framing=ESF
[10]
active=yes
alarms=RED/LFA/LMFA
description=T4XXP (PCI) Card 2 Span 2
name=TE4/2/2
manufacturer=Digium
devicetype=Wildcard TE410P (4th Gen) (VPMOCT128)
location=PCI Bus 10 Slot 04
basechan=217
totchans=24
irq=50
type=digital-T1
syncsrc=0
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=B8ZS,AMI
framing_opts=ESF,D4
coding=B8ZS
framing=ESF
[11]
active=yes
alarms=RED/LFA/LMFA
description=T4XXP (PCI) Card 2 Span 3
name=TE4/2/3
manufacturer=Digium
devicetype=Wildcard TE410P (4th Gen) (VPMOCT128)
location=PCI Bus 10 Slot 04
basechan=241
totchans=24
irq=50
type=digital-T1
syncsrc=0
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=B8ZS,AMI
framing_opts=ESF,D4
coding=B8ZS
framing=ESF
[12]
active=yes
alarms=RED/LFA/LMFA
description=T4XXP (PCI) Card 2 Span 4
name=TE4/2/4
manufacturer=Digium
devicetype=Wildcard TE410P (4th Gen) (VPMOCT128)
location=PCI Bus 10 Slot 04
basechan=265
totchans=24
irq=50
type=digital-T1
syncsrc=0
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=B8ZS,AMI
framing_opts=ESF,D4
coding=B8ZS
framing=ESF

lspci
09:04.0 Communication controller: Digium, Inc. Wildcard TE410P/TE412P
quad-span T1/E1/J1 card 3.3V (rev 02)
0a:02.0 Communication controller: Digium, Inc. Wildcard TE410P/TE412P
quad-span T1/E1/J1 card 3.3V (rev 02)
0a:03.0 Communication controller: Digium, Inc. Wildcard TE410P/TE412P
quad-span T1/E1/J1 card 3.3V (rev 02)

Thanks
Dave

2 thoughts on - TE410P hardware problems

  • Hi,

    We opened the server an checked that the cards were seated correctly and
    they are. I will have the tech completely remove them tomorrow and try
    again. I will post the results.

    Dave

  • If it doesn’t go green when you put a hard loopback on the port, then contact Digium support.